An Introduction to Precious Metal Clay Jewelry

Moderators: PinkDiamond, John

Post Reply
User avatar
PinkDiamond
Posts: 15402
Joined: Thu Jun 04, 2015 9:30 pm
Location: Ozark Mountains

An Introduction to Precious Metal Clay Jewelry

Post by PinkDiamond »

This one's by Jeff Graham, on how easy it is to use PMC to make jewelry, and I love the patterns in the clay that he shows, so since this is picture heavy, I'll take you just past the patterns, and you can use the link at the bottom to finish the rest of the instructions on how to make jewelry from it. Enjoy! :)

An Introduction to Precious Metal Clay Jewelry
by Jeff R. Graham
Summary
Precious metal clay (or PMC) is just what it sounds like: fine silver or gold ground extremely small and suspended in a binder to create clay. Just like what you played with as a kid. For novice jewelry makers, learning to create with precious metal clay is easy. For jewelry makers of any experience level, working with this material takes little time. It also requires little space in your workshop.
Reading time: 6 min 53 sec


Image
A precious metal clay pin with a red cubic zirconia (CZ) stone by Carl Stanley. Since heat usually doesn’t bother CZs, he put it into the jewelry piece first and then fired it. This is a common practice with precious metal clay jewelry and gemstones without heat sensitivity.

"Editor’s Note: The late Jeff Graham attended the Kraftwerks 2003 event in Ontario, California as a featured “Kraft Master.” He shared his observations of Carl Stanley’s precious metal clay demonstration.

Honestly, before I saw Carl Stanley’s very informative demonstration, I had no interest in precious metal clay. However, now I can see a lot of unique applications for this material.

Why Use Precious Metal Clay?

Once you mold and shape this material, you can fire it in a casting oven. Depending on the type of clay, you can even fire it with a torch.

PMC offers several advantages.

* First, it’s very fast and simple to work with. This material has a very small learning curve for beginners. It doesn’t require traditional jewelry making skills, such as soldering or forging.

* Second, PMC requires little space. You don’t even need a workshop, just a small space on your workbench or table. As for traditional tools, you’ll only need a burn out oven or torch.

* Third, clubs and schools often teach classes on PMC. If you don’t have an oven, look for a local class. You can get access easily.

Image
Carl Stanley lecturing on precious metal clay.

PMC comes in a plastic wrapped block just like any clay. Of course, it costs more. You can roll, shape, mold, glue, stamp, and extrude this material. You can do just about anything else you can imagine with PMC to create jewelry pieces. Then, set it aside to dry out and harden so it’ll keep its shape. Next, fire it and then… Magic! Silver and gold jewelry.

Image

As you can see, PMC can be manipulated in many ways with many techniques.

Plastic Molding Materials

Notice the lavender pieces of plastic around Carl’s workspace? This is a plastic material you can use to make molds or texture stamps.

Image

The plastic molding material comes in sheets as well as clay-like and liquid forms. Basically, you can work it like the PMC itself. You can also make forms from it.

Image

When the plastic mold material cures, it becomes somewhat like linoleum or tire rubber. It will hold whatever shape you created with a high level of detail. You can then use it to mold the clay.

Precious Metal Clay and Plastic Shrinkage

Both the PMC (after firing) and plastic molding material (after curing) have some shrinkage. The degree depends on the type of clay or molding. Some materials hardly shrink at all, while others shrink as much as 30% or so.

However, you can take advantage of this shrinkage. You can actually make pieces smaller by molding, firing and remolding.

For example, you can make a smaller version of this cactus silver pin you’ve already created without going through the labor of carving the pin all over again. You can create a mold of the original pin using the plastic molding material.

Image

Simply press the original pin into the soft molding material and you’ll create a duplicate image. Then, take some PMC and make a new pin from the new mold. Fire the PMC and, depending on the type of clay (and its shrinkage), you’ll have a smaller duplicate of the original cactus pin. If you want more same-sized duplicate pins, use the same mold. If you want even smaller duplicates, create new molds with the ever shrinking pins.

With this method, you can quickly and easily create molds for identical pieces in various sizes. Compare this with a traditional method like wax casting. For small production custom jewelry, this process will save a significant amount in labor and material costs.

Image

Please note, you can also add additional details very easily to the molding material. With various tools, you can cut, scribe, or indent the additions into the material while soft.

Precious Metal Clay Textures

Take a look at these examples of different textures created using PMC. As you can see, there are endless possibilities.

Image
Image
Image

Creating Precious Metal Clay Jewelry

Carl Stanley created the PMC pin shown at the top of the article in no more than hour. He was lecturing while making it, too. So you can imagine how fast something like that piece could be made under normal working conditions.
Another view of Carl Stanley’s PMC and CZ pin.

This is how he created it.

Rolling

First, the PMC was rolled out to the desired thickness. Note: Carl placed two sticks of the same thickness on either side of the clay before rolling. Thus, when he rolled over the top of the sticks, the clay would have a uniform thickness.

Texture and Cutting

Once the clay was rolled evenly and large enough, Carl applied different texture stamps to it to create the desired effect. Then, he placed a paper pattern of the pin on top of the clay as a guide for cutting out the pieces. With an X-acto knife, he cut around the pattern to create the pin pieces. The cut pieces were put aside to dry out before fitting, sanding, and assembling. (Depending on the temperature and humidity where you live, the drying stage can be fairly short, from 30 minutes to an hour, or maybe a couple of hours). ... "

https://www.gemsociety.org/article/prec ... emologists
PinkDiamond
ISG Registered Gemologist


· ´¨¨)) -:¦:-¸.·´ .·´¨¨))
((¸¸.·´ ..·´ There are miracles left for you to do .... -:¦:- -:¦:-
-:¦:- ((¸¸.·´* It all begins inside of you. ;)
Post Reply